Back to all

Power Steering Service in Troy

November 26, 2017



Most Troy drivers are too young to remember life before power steering - cranking those great big steering wheels! It was a pretty good workout. Now power steering is standard. Let's look at how it works. The heart of any power steering system is its pump. The pump pressurizes the power steering fluid that provides assist for steering. Most pumps are driven by a belt that is run by the engine; a few are electrically powered. A high-pressure hose passes fluid from the pump to the steering gear. A low pressure hose returns the fluid back to the pump.

These hoses can develop leaks, so it is a good idea for Troy drivers to have them inspected at every oil change. Low fluid can damage the power steering pump. That is why power steering fluid level is on the checklist for a full-service oil change. The fluid needs to be compatible with the hoses and seals, so check your owner's manual for the right type - or just ask your friendly and knowledgeable pros at Gary Knurek GoodYear in Troy.

The fluid cleans, cools and lubricates the power steering system. It breaks down as the years go by and collects unwanted moisture, so Troy drivers need to replace it from time to time. Many vehicle manufacturers specify power steering service intervals. Unfortunately, this important service is sometimes left off the car maintenance schedule for many of us. So, when in doubt, every 25,000 miles/40,000 km or two years is a good fallback. Your technician at Gary Knurek GoodYear will use a detergent to clean the system, flush out the old fluid and replace it with the good stuff.

Here are some  warning signs of trouble with your power steering: It's harder to turn the wheel, there's erratic power assist, you hear loud whining coming from the pump (which may be difficult to hear over the loud whining coming from the backseat), you have to top-off the fluid frequently, or you hear squealing belts. Remember to never hold the steering wheel to the far right or left for more than a few seconds at a time. That will wear out your power steering pump quickly.

Other steering components can be bent or damaged from wear or hard knocks: ball-joint, idler-arm, steering-gear, steering-knuckle and tie rod to name a few. Warning signs here are steering play, wandering, uneven tire wear and an off-center steering wheel. An annual alignment check at Gary Knurek GoodYear in Troy will reveal bent or damaged steering components.

Most SUV's, pick-ups and rear-wheel-drive cars need regular front-wheel-bearing service.

The bearings should be cleaned and inspected. If they are excessively worn, they need to be replaced. The bearings are then repacked in clean grease. The team at Gary Knurek GoodYear also recommends the wheel-seal be replaced when the bearings are serviced. Like everything else, check your owners' manual maintenance schedule. It's usually required around every two years or 40,000 miles/64,000 km. If you drive through water in the Troy area, the bearings will need service more often.

Gary Knurek GoodYear
1973 Livernois
Troy, Michigan 48083
248-362-0350

 

Need Service?

Request a Quote

More articles from Gary Knurek, Authorized GoodYear Dealer

No Shake, Just Smooth

July 12, 2026

When your vehicles wheels are out of balance, theyll likely give you some clues. Your steering wheel might shake, the floor or seat vibrates and you might find your vehicle pulling to one side. Other signs? Your tires might wear unevenly and may make odd noises. Plus, fuel economy might not be ... More

Stop Right There!

July 5, 2026

Your vehicles brakes are only as good as its master cylinder. This part is truly is the heart of your braking system, because if it isnt working the way it should, the rest of the brake system cant either. The master cylinder is what takes the pressure you put on the brake pedal and ultimately... More

Why Timing Belt Maintenance Can Save Your Engine

June 28, 2026

One part of your vehicle you probably never think of is the timing belt. It coordinates the rotation of the crankshaft (which converts the up and down motion of the pistons into rotation motion) and the camshaft (which opens and closes your engines valves). Its vital that the timing of these mov... More